Konica-minolta MS7000 MKII User Manual

2010.2UC-8User’s GuidePrinted in Japan

SAFETY INFORMATIONviii • When unplugging the power cord, be sure to hold onto the plug.Pulling on the power cord could damage the cord, resulting in

SAFETY INFORMATIONixPrecautions for Routine• Do not store toner units, PC drum units, and other supplies andconsumables in a place subject to direct s

SAFETY INFORMATIONx • N’utilisez jamais cet appareil en présence d’ammoniaque ou d’autresproduits chimiques ou gaz. Le non-respect de cette précautio

SAFETY INFORMATIONxiWelcomeThis User's Guide explains how to operate the unit and replenish its supplies. It also gives some troubleshooting tips

Contentsxii Contents1 Notes to Operators and Key Operators1.1 The following safety rules should be observed...1-1FCC Part 15 - R

Notes to Operators and Key Operators1-11 Notes to Operators and Key Operators1.1 The following safety rules should be observed1. The unit should be ke

Notes to Operators and Key Operators1-2 Interference-Causing Equipment Standard (ICES-003 ISSUE 4) (For Canada Users)This Class A digital apparatus c

Part Identification2-12 Part Identification2.1 Part Identification1 Guide Roller (Left)2 Reel Shaft3 Film Pressure Glass4 Connecting Cord (I/F Cab

Operation3-1 3 Operation3.1 Selecting the Film Width 16/35mm1 Release the Stopper Ring which holds the Guide Roller.2 Pull out the front part of the

Operation3-23.2 Loading the Roll Film1 Mount the Roll Film onto the Reel Shaft and unwind the leading edge of the film.2 Take hold of the Carrier Hand

Operation3-3 3.3 Feeding the Film1 Turn the Speed Control Knob clockwise or counter-clockwise to feed the film in the forward or reverse direction. T

Operation3-43.4 Rewinding the Film1 Take hold of the Carrier Handle and pull it gently out as far as it will go. This causes the Film Pressure Glass t

Operation3-5 3.5 Operating Fiche1 Take hold of the Carrier Handle and pull it forward fully, then the Film Pressure Glass will open.2 Insert the film

Daily Maintenance4-14Daily Maintenance4.1 Cleaning the Carrier Glasses1 Clean and remove any dust or debris on the Carrier Glass’s surface with a damp

Installation5-1 5Installation5.1 Installation1 Turn the Guide Rail of the main unit counterclockwise at 90 degrees.2 Pull the Carrier to the let full

Installation5-24 Plug the Connecting Cord Connector of the Carrier into the Socket in the machine dedicated to this Carrier.5 Install the Lens Unit al

Miscellaneous6-1 6 Miscellaneous6.1 SpecificationsFilm Type 16mm Open Reel Roll Film, 35mm Open Reel Roll Film, Microfiche, Aperture Card, JacketFilm

Copyright20102010.27162-7701-01UUsKYOKKO SEIKO CO., LTD.Printed in JapanThe information contained in this manual is subject to change without notice t

SAFETY INFORMATIONiSAFETY INFORMATIONThis section contains detailed instructions on the operation and maintenance of this machine. To achieve optimum

SAFETY INFORMATIONii INFORMATIONS DE SÉCURITÉCette section contient des instructions détaillées sur l'utilisation et l'entretien de cette m

SAFETY INFORMATIONiii• Do not modify this product, as a fire, electrical shock, or break-down could result. If the product employs a laser, the laser

SAFETY INFORMATIONiv • Do not unplug or plug in the power cord with a wet hand, as anelectrical shock could result.• Né branchez ni débranchez jamais

SAFETY INFORMATIONv• Ne posez jamais de vase ou tout autre récipient contenant de l’eau, ainsique de petits objets métalliques tels que des trombones

SAFETY INFORMATIONvi • Do not use flammable sprays, liquids, or gases near thisproduct, as a fire could result.• Do not leave a toner unit or drum un

SAFETY INFORMATIONvii• N’installez pas cet appareil sur une surface instable ou inclinée, etévitez également les endroits particulièrement exposés aux