Konica-minolta KIP Color 80 User Manual

Version A3 KIP Color 80 Printer Operator’s Guide Guide 2

1-51. 3 Features (1) Contact Development Technology with non-magnetic mono-component toner Provides high definition lines and consistent

1-953. 2. 8 Mis-feed around the Transportation Unit 1 Region (Code: J-0121, J-0221 & J-0421) When the roll media is mis-

1-96 2. Check if the mis-fed is cut or not by pulling from between the Transportation Unit 3 & 4. Whether the media is cut or not de

1-97 4. Check if the media is found around the Transportation Unit 4. Whether or not the media is found decides what to do next. • If the me

1-98 6. Rotate the Cutter Handle one revolution in the direction of arrow to cut the roll media manually. 7. Remove t

1-99 8. Close the Transportation Unit 4 and Right Side Door (if opened). 9. Initial Cut is recommended to straighten the le

1-1003. 2. 9 Mis-feed around the Transportation Unit 2 Region (Code: J-0122, J-0222 & J-0422) When the roll media is mis

1-101 2. Check if the mis-fed is cut or not by pulling from between the Transportation Unit 3 & 4. Whether the media is cut or not d

1-102 4. Check if the media is found around the Transportation Unit 4. Whether or not the media is found decides what to do next. • If the m

1-103 6. Rotate the Cutter Handle one revolution in the direction of arrow to cut the roll media manually. 7. Remove

1-104 8. Close the Transportation Unit 4 and Right Side Door (if opened). 9. Initial Cut is recommended to straighten the le

1-61. 4 Specifications Subject Specification Model KIP Color 80 Type Console Printing method LED - Electro Photography Color CMYK Photoconduct

1-1053. 2.10 Mis-feed around the Transportation Unit 3 Region (Code: J-0123, J-0223 & J-0423) When the roll media is mis-

1-106 2. Check if the mis-fed is cut or not by pulling from between the Transportation Unit 3 & 4. Whether the media is cut or not d

1-107 4. Check if the media is found around the Transportation Unit 4. Whether or not the media is found decides what to do next. • If the m

1-108 6. Rotate the Cutter Handle one revolution in the direction of arrow to cut the roll media manually. 7. Remove

1-109 8. Close the Transportation Unit 4 and Right Side Door (if opened). 9. Initial Cut is recommended to straighten the le

1-1103. 2.11 Mis-feed around the Transportation Unit 4 Region (Code: J-0124, J-0224 & J-0424) When the roll media is mis-

1-111 2. Check if the mis-fed is cut or not by pulling it. Whether the media is cut or not decides what to do next. • If the mis-fed

1-112 5. Rotate the Cutter Handle one revolution in the direction of arrow to cut the roll media manually. 6. Remove

1-113 7. Close the Transportation Unit 4 and Right Side Door (if opened). 8. Initial Cut is recommended to straighten the l

1-1143. 2.12 Mis-feed in the Fuser Region (Code: J-0131, J-0231 & J-0431) When the roll media is mis-fed around the Fuser region, any of J-01

1-7 Subject Specification Environmental condition Temperature 10 to 32.5 degrees centigrade (50 - 89 F) Humidity 30 to 70% RH

1-115 3. Looking into the machine through the open hole on the inside plate, check if the mis-fed is held between the rollers in the F

1-116 5. If the leading edge of media is hidden under the parts as the following left photo, pull it out so that the media can be removed und

1-117 6. Eject the mis-fed media manually by rotate the Fuser Roller Handle in the direction of arrow by hand.

1-118 8. Check if the media is found around the Transportation Unit 4. Whether or not the media is found decides what to do next. • If the m

1-11911. Remove the media from the Transportation Unit 4 region. 12. Close the Transportation Unit 4 and Right Side Door.

1-1203. 3 Open Errors (Codes: U-xxxx) If any door, cover or unit is open, the Open Indicator on the Operation Panel lights orange. The location

1-1213. 3. 1 Roll Deck 1 open (Code: U-0101) U-0101 is indicated when the Roll Deck 1 is opened or not locked completely. Close the Roll Deck 1

1-1223. 3. 4 Roll Deck 4 open (Code: U-0104) U-0104 is indicated when the Roll Deck 4 is opened or not locked completely. Close the Roll Deck 4

1-1233. 3. 6 Bypass Feeder open (Code: U-0111) U-0111 is indicated when the Bypass Feeder is opened or not locked completely. Close the Bypass

1-1243. 3. 9 Transportation Unit 2 open (Code: U-0122) U-0122 is indicated when the Transportation Unit 2 is opened or not locked completely. C

1-81. 5 Appearance 1. 5. 1 Front view Name of part Function Power Switch Turns on the KIP Color 80. Bypass

1-1253. 3.12 Fuser Cover open (Code: U-0130) U-0130 is indicated when the Fuser Cover is opened or not locked completely. Close the Fuser Cover

1-1263. 3.15 Waste Toner Box is not set (Code: U-0150) U-0150 is indicated when the Waste Toner Box is not set correctly. Set the Waste Toner B

1-1273. 4 Call Service Errors (Codes: E-xxxx) When a significant problem occurs, the KIP Color 80 stops the operation indicating any “service ca

1-128 Service call error code Error Name E-2115 Image corona 1 cleaning error (Early) E-2116 Image corona 1 cleaning error (Over current) E-2117

1-129 Service call error code Error Name E-2414 Image corona 4 cleaning error (Delay) E-2415 Image corona 4 cleaning error (Early) E-2416 Image c

1-1303. 5 Error Indicators The Error Indicators on the Operation Panel informs the type of error. Open Indicator Web Clea

1-1313. 5. 1 Open Indicator The Open Indicator lights orange when any door, cover or unit is open. An open error code is indicated on th

1-1323. 5. 2 Web Cleaner Empty Indicator The Web Cleaner Empty Indicator flashes red when the Web Cleaner is near empty. Some more print is st

1-1333. 5. 4 Roll Empty Indicator The Roll Empty Indicator lights red when the used roll media is emptied. See [1.2.3 Replacing t

1-1343. 5. 5 Mis-feed Indicator The Mis-feed indicator lights red when a printing media is mis-fed anywhere in the KIP Color 80. A

1-91. 5. 2 Right side view Counter A Counter B Dehumidify Heater Switch Cutter Handle Dus

1-135 Mis-feed code Error Name Reference page for the solution J-0123 J-0223 J-0423 Transportation Unit 3 Region 1-105 J-0124 J-0224 J-0424 Transp

1-1363. 6 Other Indications (Not error) 3. 6. 1 Flash of Ready Indicator The Ready Indicator may suddenly starts flashing during normal us

1-1373. 6. 2 Flash of Wire-Clean Key The Wire-Clean Key may flash green synchronized with the Ready Indicator when turning on the KIP Color 80.

1-1383. 6. 3 “In Use” Indicator Even if the KIP Color 80 is printing, it may be allowed to open a Roll Deck for replacing the roll media without

1-139 As the media feeding path runs through the interior of all Roll Decks, the roll medi

1-1403. 7 Treatment for Print Quality Problems 3. 7. 1 Unnecessary vertical line image on the print An unnecessary vertical line which loo

1-1413. 7. 2 Crease of the printing media The printing media may be creased when printed in a humid environment. • Store the printing media co

1-142 4 IPS Dashboard 4. 1 KIP Tab - Main Screen The main screen of the KIP Color 80 - IPS Dashboard consists of 3 large icons under th

1-1434. 2 About Tab The “About” tab displays current versions of software installed on the KIP color 80 IPS. NOTE: The above versions are o

1-144 4. 3. 1 Regional Setting This dropdown is used for different regions for keyboard configurations and preferred language. Please select the

1-10 Name of part Function Cutter Handle Can manually cut the mis-fed media rotating the Cutter Handle. Fuser Handle Can remove the mos-fed media

DIGITAL COLOR PRINTER KIP Color 80 User’s Manual Version A.3 Published by Katsuragawa Electric Co., Lt

1-111. 5. 3 Rear view Fuser Cover Fuser Upper Cover Transportation Unit 1 Transportation

1-12 Name of part Function Fuser Upper Cover Can access the media mis-fed around the entrance of the Fuser Unit. Fuser Cover Can access the media

1-131. 5. 4 Operation Panel The Operation Panel on the upper right of front face is available for several settings. It also indicates several st

1-14 No. Name of part Function Refer to page; 14 Mis-feed / Open Location Indicator Indicates the location of mis-fed media by lighting any LED i

(1)Thank you for purchasing the KIP Color 80 Digital Color / Mono Large Format Printer. This USER’S MANUAL contains functional and operational expla

1-151. 5. 5 Media & Toner Information Panel The Media & Toner Information Panel indicates the information of roll media on each Roll Dec

1-162 Operation Details 2. 1 Turning on the KIP Color 80 1. Plug the KIP Color 80 to a dedicated wall outlet. 2. Press “|”

1-17 4. KIP Color 80 starts warming up. The Ready Indicator on the operation Panel flashes green during warming up.

1-182. 2 Turning off the KIP Color 80 Press “ ” side of the Power Switch on the front to turn off the KIP Color 80.

1-192. 3 Replacing the Roll Media The Roll Empty Indicator lights red when the used roll media is emptied during printing. Install a new roll m

1-20 1. Pulling up the handle to unlock the Roll Deck, and draw out the deck. 2. Rotate the Roll Spool one revolution in t

1-21 3. Pressing down the green lever to release the core of roll media, and pull out the Roll Spool from the core. 4. Press

1-22 5. Align the edge of roll media with the concerning size guide, and then release the green lever to fix the roll media onto the R

1-23 7. As there is a slit for receiving a cutter knife on each Roll Deck, cut off the leading part of roll media to straighten the leading e

1-24 9. Media Selector is on the right of the Roll Deck. Press any of “PLAIN PAPER”, “VELLUM / TRACING”, “FILM” and “GLOSS” according to the

(2) The following warnings are very important in order to safely use this product. These notes are very important in preventing danger to the

1-252. 4 Setting Cut Sheet Media to Bypass Feeder Cut sheet media can be fed from the Bypass Feeder. Each size has its own availability for ori

1-262. 4. 1 Multi-feeding of cut sheet media Multi-feeding is available when a small cut sheet media is used. “Small sizes” are as follows.

1-27 3. Arrange the edges of multiple media, put them on the Bypass Feeder by landscape position, and move them forward until contacted to fe

1-282. 4. 2 Singular feeding of cut sheet media A large cut sheet media can not be fed by multi-feeding. Please feed it singularly as instructed

1-29 NOTE As curled cut sheet media will cause a mis-feed, straighten the media as far as possible before printing.

1-302. 5 Replacing the Toner Cartridge The Toner Empty Indicator on the Operation Panel lights red when any of 4 Toner Cartridges is empty. On

1-31 1. Open the Right Side Door. 2. Rotate the Toner Cartridge 180 degrees in the direction of arrow until it is stopped. R

1-32 3. Choose the new Toner Cartridge of the same color, and shake it well to loosen the toner. 4. Insert the Toner Cartridge int

1-33 6. Strip off the green seal to open the cartridge. 7. Close the Right Side Door. Green seal NOTE

1-342. 6 Replacing the Waste Toner Box The Waste Toner Full Indicator on the Operation Panel lights red when the Waste Toner Box is completely

(3) WARNING Ground the product with a correct ground source or

1-35 2. Remove the Waste Toner Box. 3. Strip off the release paper beside the open hole. 4. Close the open ho

1-36 5. Assemble a folded Waste Toner Box. 6. Strip off the protection papers on 3 tabs, and apply these 3 tabs to the side face of

1-37 7. Holding the free tab, set the Waste Toner Box into the machine so that the hole on the top of the box is located on the rear s

1-382. 7 Dehumidifying the Roll Media A print defect may occur if the roll media is very humid. The usual defects are “crease of media” and “la

1-39 2. Press the “H” side of the Dehumidify Heater Switch to turn on the Dehumidify Heater. (Press the “L” side to turn off.)

1-402. 8 Initial Cut (Straighten the leading edge of roll media) A new roll media tends to have a rough or folded leading edge.

1-412. 9 User Modes KIP Color 80 provides 14 User Modes. Please note that not all of these modes are to be used and are meant more for service

1-422. 9. 1 User Mode 01 (Test Print Start Mode) User Mode 01 can start a Test Print. [Operation] 1. Press the Menu Key once to

1-43 2. Press the Enter Key to start test printing. The KIP Color 80 will perform test printing depending on your test print settings. “Poo”

1-442. 9. 2 User Mode 02 (Warm Sleep Mode) Warm Sleep Mode can be worked or cancelled, and the timer setting is available as well if Warm Sleep

(4) CAUTION Do not install the machine in a humidified room or

1-45 4. Press the Enter Key to decide the ON/OFF setting. Then the next setting item “timer setting” becomes available to change. (Setting wi

1-462. 9. 3 User Mode 03 (Cold Sleep Mode setting) The timer setting for the Cold Sleep Mode is available. [Operat

1-47 3. Set the timer for the Cold Sleep Mode selecting a required time pressing [ ] and [ ] keys. Selectable timers are 10, 15, 20, 3

1-482. 9. 4 User Mode 04 (Temporary clearance of E-2132) Service call error E-2132 might be temporarily cleared by easing the error check level,

1-49 3. Select “On” or “OFF” with pressing [ ] and [ ] keys. On : Normal error check level OFF : Low error

1-502. 9. 5 User Mode 05 (Temporary clearance of E-2232) Service call error E-2232 might be temporarily cleared by easing the error check level,

1-51 5. Press the Online Key to cancel the User Mode 05. 6. Turn off/on the KC80 to reset the error code indication. Menu Ente

1-522. 9. 6 User Mode 06 (Temporary clearance of E-2332) Service call error E-2332 might be temporarily cleared by easing the error check level,

1-53 5. Press the Online Key to cancel the User Mode 06. 6. Turn off/on the KC80 to reset the error code indication. Menu Ente

1-542. 9. 7 User Mode 07 (Temporary clearance of E-2432) Service call error E-2432 might be temporarily cleared by easing the error check level,

1-1 Table of Contents 1 Before System Use 1- 3 1. 1 Installation Requirements 1- 3 1. 2 Originals Prohibited

1-55 5. Press the Online Key to cancel the User Mode 07. 6. Turn off/on the KC80 to reset the error code indication. Menu Ente

1-562. 9. 8 User Mode 08 (Temporary clearance of E-2142) Service call errors E-2142 might be temporarily cleared by easing the error check level

1-57 3. Select any of “OFF”, “On1” and “On2” with pressing [ ] and [ ] keys. OFF : Low error check level On

1-582. 9. 9 User Mode 09 (Temporary clearance of E-2242) Service call error E-2242 might be temporarily cleared by easing the error check level,

1-59 5. Press the Online Key to cancel the User Mode 09. 6. Turn off/on the KC80 to reset the error code indication. Menu Ente

1-602. 9.10 User Mode 10 (Temporary clearance of E-2342) Service call error E-2342 might be temporarily cleared by easing the error check level,

1-61 5. Press the Online Key to cancel the User Mode 10. 6. Turn off/on the KC80 to reset the error code indication. Menu Ent

1-622. 9.11 User Mode 11 (Temporary clearance of E-2442) Service call error E-2442 might be temporarily cleared by easing the error check level,

1-63 5. Press the Online Key to cancel the User Mode 11. 6. Turn off/on the KC80 to reset the error code indication. Menu Ente

1-642. 9.12 User Mode 12 (Test Print setting – Output mode) It is possible to set the output mode of Test Print to any of the following 3. Opera

1-23. 2. 8 Mis-feed around the Transportation Unit 1 Region (Code: J-0121, J-0

1-65 3. Select any of “Prn”, “C_1” and “C_2” with pressing [ ] and [ ] keys. Prn : Normal test print mode

1-662. 9.13 User Mode 13 (Test Print setting - Selection of Roll Deck) It is possible to select the Roll Deck used for test printing. 1. Pres

1-67 5. Press the Online Key to cancel the User Mode 13. Menu Enter OnlineMenu Enter O n line NOTE Online Key will cancel the

1-682. 9.14 User Mode 14 (Test Print setting - Selection of media type [type #X]) It is possible to specify the media type (t

1-69 5. Press the Online Key to cancel the User Mode 14. Menu Enter OnlineMenu Enter O n line NOTE Online Key will cancel t

1-703 Error Messages 3. 1 General Outlines of Error Codes / Error Indications If any error occurs on the KIP Color 80, the

1-71 Error Code / Error Indication Error Name Reference page for the solution J-0112 J-0212 J-0412 Mis-feed around the Bottom Corner Region 1-92 J-

1-72Error Code / Error Indication Error Name Reference page for the solution E-0001 Fuser temperature rising error 1-127 E-0002 Fuser abnormal hi

1-73 Error Code / Error Indication Error Name Reference page for the solution E-2321 Image corona 3 output error 1-127 E-2322 Transfer corona 3 o

1-743. 2 Mis-feed Errors (Codes: J-xxxx) If a mis-feed of printing media occurs anywhere in the KIP Color 80, the Mis-feed Indicator on the Oper

1-3 1 Before System Use 1. 1 Installation Requirements The following conditions are required for installation of the equipment. (1) Power

1-75 NOTE (1) Some sheets of media may be staying in the KIP Color 80 simultaneously as the following pict

1-763. 2. 1 Mis-feed around the Roll Deck 1 Region (Code: J-0101, J-0201 & J-0401) When the roll media is mis-fed in the

1-77 3. Straighten the leading edge by cutting off the damaged part with a cutter knife. 4. Insert the leading edge of ro

1-78 6. Initial Cut is recommended to straighten the leading edge perfectly. Select the Roll Deck No.1 pressing the SELECT Key, and press the

1-793. 2. 2 Mis-feed around the Roll Deck 2 Region (Code: J-0102, J-0202 & J-0402) When the roll media is mis-fed in the

1-80 3. Straighten the leading edge by cutting off the damaged part with a cutter knife. 4. Insert the leading edge of rol

1-81 6. Initial Cut is recommended to straighten the leading edge perfectly. Select the Roll Deck No.2 pressing the SELECT Key, and press the

1-823. 2. 3 Mis-feed around the Roll Deck 3 Region (Code: J-0103, J-0203 & J-0403) When the roll media is mis-fed in the

1-83 3. Straighten the leading edge by cutting off the damaged part with a cutter knife. 4. Insert the leading edge of rol

1-84 6. Initial Cut is recommended to straighten the leading edge perfectly. Select the Roll Deck No.3 pressing the SELECT Key, and press the

1-41. 2 Originals Prohibited from Duplication It may be illegal to duplicate or copy certain types of originals and you may be punished by local

1-853. 2. 4 Mis-feed around the Roll Deck 4 Region (Code: J-0104, J-0204 & J-0404) When the roll media is mis-fed in the

1-86 3. Straighten the leading edge by cutting off the damaged part with a cutter knife. 4. Insert the leading edge of rol

1-87 6. Initial Cut is recommended to straighten the leading edge perfectly. Select the Roll Deck No.3 pressing the SELECT Key, and press the

1-883. 2. 5 Mis-feed around the Bypass Feeder Region (Code: J-0105, J-0205 & J-0405) When the roll media is mis-fed in t

1-893. 2. 6 Mis-feed around the Cutter Region (Code: J-0111, J-0211 & J-0411) When the roll media is mis-fed around the

1-90 3. Open the Right Side Door again, if it is closed. 4. Rotate the Cutter Handle one revolution in the direction of arrow to cut

1-91 6. Close the Transportation Unit 4 and Right Side Door. 7. Initial Cut is recommended to straighten the leading edge p

1-923. 2. 7 Mis-feed around the Bottom Corner Region (Code: J-0112, J-0212 & J-0412) When the roll media is mis-fed arou

1-93 3. After removing the mis-fed media from the Bottom Corner region, check if some more media is found around there. Whether or not the me

1-94 6. Remove the media from the Transportation Unit 4 region. 7. Close the Transportation Unit 4 and Right Side Door (if opene